nf-core/crisprseq

Edit

Introduction

The nf-core/crisprseq pipeline allows the analysis of CRISPR edited CRISPR pooled DNA. It can evaluate important genes from knock-out or activation CRISPR-Cas9 screens.

Running the pipeline

The typical command for running the pipeline is as follows:

nextflow run nf-core/crisprseq --analysis screening --input samplesheet.csv --library library.csv --outdir <OUTDIR> -profile docker

The following required parameters are here described. If you wish to input a raw count or normalized table, you can skip the samplesheet parameter as well as the library one and directly input your table using count_table --count_table your_count_table. Your count table should contain the following columns : sgRNA and gene. You can find an example here If your count table is normalized, be sure to set the normalization method to none in MAGeCK MLE or MAGeCK RRA using a config file.

Full samplesheet

The samplesheet can have as many columns as you desire, however, there is a strict requirement for the first 4 columns to match those defined in the table below.

sample,fastq_1,fastq_2,condition
SRR8983579,SRR8983579.small.fastq.gz,,control
SRR8983580,SRR8983580.small.fastq.gz,,treatment

An example samplesheet has been provided with the pipeline.

cutadapt

MAGeCK count which is the main alignment software used is normally able to automatically determine the trimming length and sgRNA length, in most cases. Therefore, you don’t need to go to this step unless MAGeCK fails to do so by itself. If the nucleotide length in front of sgRNA varies between different reads, you can use cutadapt to remove the adaptor sequences by using the flag --five_prime_adapter or --three_prime_adapter .

bowtie2

The MAGeCK count module supports bam files, which allows you to align with bowtie2 first. If you wish to do so (for instance to allow mapping reads to the library with mismatches or to set the aligner with specific flags) you can provide a fasta file with --fasta encoding the library. Currently, you also still need to provide the tab-separated library file with --library.

library

If you are running the pipeline with fastq files and wish to obtain a count table, the library parameter is needed. The library table has three mandatory columns : id, target transcript (or gRNA sequence) and gene symbol. An example has been provided with the pipeline. Many libraries can be found on addgene.

After the alignment step, if you are performing KO (Knock-Out) screens, you can choose to correct gene-independent cell responses to CRISPR-Cas9 targeting using CRISPRcleanR. If you are performing a CRISPR interference or activation screen, this step is not needed.

The pipeline currently supports 3 algorithms to detect gene essentiality, MAGeCK RRA, MAGeCK MLE and BAGEL2. MAGeCK MLE (Maximum Likelihood Estimation) and MAGeCK RRA (Robust Ranking Aggregation) are two different methods provided by the MAGeCK software package to analyze CRISPR-Cas9 screens. BAGEL2 identifies gene essentiality through Bayesian Analysis. We recommend to run MAGeCK MLE and BAGEL2 as these are the most used and most recent algorithms to determine gene essentiality.

Running CRISPRcleanR

CRISPRcleanR is used for gene count normalization and the removal of biases for genomic segments for which copy numbers are amplified. Currently, the pipeline supports annotation libraries already present in the R package or user-provided annotation files. Most used library already have an annotation dataset which you can find here. To use CRISPRcleanR normalization, use --crisprcleanr library, library being the exact name as the library in the CRISPRcleanR documentation (e.g: “AVANA_Library”). Otherwise, if you wish to provide your own file, please provide it in CSV format, and make sure it follows the following format (with the comma in front of “CODE” included):

Running MAGeCK MLE and BAGEL2 with a contrast file

To run both MAGeCK MLE and BAGEL2, you can provide a contrast file with the flag --contrasts with the mandatory headers “treatment” and “reference”. These two columns should be separated with a dot comma (;) and contain the csv extension. You can also integrate several samples/conditions by comma separating them in each column. Please find an example here below :

A full example can be found here.

Venn diagram

Running MAGeCK MLE and BAGEL2 with a contrast file will also output a Venn diagram showing common genes having an FDR < 0.1.

Running MAGeCK RRA only

MAGeCK RRA performs robust ranking aggregation to identify genes that are consistently ranked highly across multiple replicate screens. To run MAGeCK RRA, you can define the contrasts as previously stated in the last section (with a .txt extension) and also specify --rra.

Running MAGeCK MLE only

With design matrices

If you wish to run MAGeCK MLE only, you can specify several design matrices (where you state which comparisons you wish to run) with the flag --mle_design_matrix. MAGeCK MLE uses a maximum likelihood estimation approach to estimate the effects of gene knockout on cell fitness. It models the read count data of guide RNAs targeting each gene and estimates the dropout probability for each gene. MAGeCK MLE requires one or several design matrices. The design matrix is a txt file indicating the effects of different conditions on different samples. An example design matrix has been provided with the pipeline. The row names need to match the condition stated in the sample sheet. If there are several designs to be run, you can input a folder containing all the design matrices. The output results will automatically take the name of the design matrix, so make sure you give a meaningful name to the file, for instance “Drug_vs_control.txt”.

With the day0 label

If you wish to run MAGeCK MLE with the day0 label you can do so by specifying --day0_label and the sample names that should be used as day0.

Running BAGEL2

BAGEL2 (Bayesian Analysis of Gene Essentiality with Location) is a computational tool developed by the Hart Lab at Harvard University. It is designed for analyzing large-scale genetic screens, particularly CRISPR-Cas9 screens, to identify genes that are essential for the survival or growth of cells under different conditions. BAGEL2 integrates information about the location of guide RNAs within a gene and leverages this information to improve the accuracy of gene essentiality predictions. BAGEL2 uses the same contrasts from --contrasts.

MAGECKFlute

The downstream analysis involves distinguishing essential, non-essential, and target-associated genes. Additionally, it encompasses conducting biological functional category analysis and pathway enrichment analysis for these genes. Furthermore, it provides visualization of genes within pathways, enhancing user exploration of screening data. MAGECKFlute is run automatically after MAGeCK MLE and for each MLE design matrice. If you have used the --day0_label, MAGeCKFlute will be ran on all the other conditions. Please note that the DepMap data is used for these plots.

Note that the pipeline will create the following files in your working directory:

work                # Directory containing the nextflow working files
<OUTDIR>            # Finished results in specified location (defined with --outdir)
.nextflow_log       # Log file from Nextflow
# Other hidden nextflow files, eg. history of pipeline runs and old logs.